Kiväärien kestotestauksen automatisointi

No Thumbnail Available
Journal Title
Journal ISSN
Volume Title
Insinööritieteiden korkeakoulu | Master's thesis
Ask about the availability of the thesis by sending email to the Aalto University Learning Centre oppimiskeskus@aalto.fi
Date
2017-02-20
Department
Major/Subject
Koneensuunnittelu
Mcode
K3001
Degree programme
Konetekniikan koulutusohjelma
Language
fi
Pages
91 + 11
Series
Abstract
Kiväärien kestoa tutkitaan ampumalla sillä osien kestorajaan asti, yleensä tuhansia tai jopa kymmeniä tuhansia laukauksia. Testaus suoritetaan täysin manuaalisesti, joka rasit- taa koeammuntaa suorittavaa henkilöstöä. Kestotestausammuntaa varten ei ole aiemmin kehitetty automaattista menetelmää, mutta tarve testauksen automatisoinnille on ole- massa lisääntyneen testaustarpeen vuoksi. Automatisointi mahdollistaisi myös kiväärien kestoon vaikuttavien tekijöiden tarkemman tutkimisen. Tämän työn tavoitteena oli kivää- rien kestotestauksen automatisointimahdollisuuksien tutkiminen ja automaattisen testi- laitteen kehittäminen. Automatisoinnilta haluttuja toiminnollisuuksia oli pohdittu jo aiemmin, mutta niitä ei oltu tarkasteltu automatisoinnin toteuttamisen kannalta. Työn aikana tehtiin laitteen vaatimusmäärittely, jonka pohjalta kehitettiin ratkaisuehdo- tus kiväärien automaattista kestotestausta varten systemaattisia suunnitteluperiaatteita käyttämällä. Laitteen toiminnasta luotiin kuvaus, josta käy ilmi vaatimusten mukaisten toimintojen toteutus. Mekaaninen suunnittelu toteutettiin lataus- ja laukaisumekanis- mien osalta. Lisäksi kiväärin kiinnityksen ja tuennan rakenne luonnosteltiin. Kestotestauksen automatisointi todettiin mahdolliseksi toteuttaa työn aikana kehitetyillä ratkaisuilla. Automatisointia varten kehitetty menetelmä ja rakenneratkaisut olivat uu- denlaisia, eivätkä suoraan pohjautuneet olemassa oleviin ratkaisuihin. Suunniteltua tes- tipenkkiä ei päästy rakentamaan tämän työn aikana. Työ loi kuitenkin hyvän pohjan tes- tipenkin jatkokehittelylle ja mahdollistaa pienellä lisäsuunnittelulla jo sellaisenaan kivää- rien automaattisen kestotestauksen ilman automatisoitua lippaanvaihtoa

The endurance of a rifle is investigated by firing it repetitively until its parts reach their endurance limit, which requires thousands or even tens of thousands of firings. The en- durance test is performed completely manually, which strains personnel executing the test. There are currently no automatic methods developed for the endurance test firing, but the need for the automatization exists due to an increase in demand for endurance testing. Additionally, the automatization facilitates investigation of the phenomena influ- encing on the endurance of a rifle. The objective of this work was to investigate the possibilities of automating the endurance testing and to develop needed solutions to realize the automatization. Desired function- alities for such device had been considered before but not in terms of the realisation of such device. During this work more precise specification for the device was composed and a solution based on the specification was developed using systematic design principles. A functional description of the device, which demonstrates fulfilment of the requirements, was also formulated. Mechanical design was performed for the loading and firing mechanisms and concept design for the support of the device. The automatization of rifle endurance testing was discovered to be viable using the solu- tions developed during this work. The developed method and solutions for the automati- zation were completely new and were not based on existing solutions. The developed test bench was not built during the work. Nevertheless, this work provides a solid foundation for follow-up development and enables as such, with limited amount of additional design, automatic endurance testing without automated magazine change
Description
Supervisor
Kuosmanen, Petri
Thesis advisor
Jussila, Henna-Riitta
Keywords
testaus, suunnittelu, testipenkki, tuotekehitys, automaatio
Other note
Citation