Low-Temperature Plasma-Enhanced Atomic Layer Deposition of Silicon Dioxide and Aluminum Oxide
Loading...
Journal Title
Journal ISSN
Volume Title
School of Electrical Engineering |
Doctoral thesis (article-based)
| Defence date: 2020-03-06
Unless otherwise stated, all rights belong to the author. You may download, display and print this publication for Your own personal use. Commercial use is prohibited.
Author
Date
2019
Major/Subject
Mcode
Degree programme
Language
en
Pages
62 + app. 41
Series
Aalto University publication series DOCTORAL DISSERTATIONS, 235/2019
Abstract
Atomic layer deposition (ALD) is a powerful deposition technique for the fabrication of highly conformal and precise thickness-controlled films. Recently, there has been a growing interest in low-temperature (< 100˚C) ALD because of the emerging applications made of organic and polymeric materials, which are known to be thermally sensitive materials. Due to the inherent disadvantages of low-temperature thermal ALD, such as slow reaction rate, long cycle time, poor film density, high impurity level and poor encapsulation properties of ultra-thin films (<5nm), the plasma-enhanced atomic layer deposition (PEALD) becomes an attractive alternative. However, there is only limited data available to show the effect of plasma parameters on film properties at low process temperatures and thus its full potential remains largely unexplored. This thesis presents the process development for low-temperature PEALD SiO2 and Al2O3 aiming to have a deeper understanding of plasma parameters vs. film properties. The work started with a study on PEALD SiO2 thin film growth, where oxygen and carbon dioxide were used as oxidizing agents. The results showed that process temperature, plasma power and exposure time used in the deposition had a strong impact on the film growth rate as well as the film properties. For example, the growth-per-cycle (GPC) increased from 0.78 to 1.15 Å/cycle with a decrease of process temperature from 200 to 90 ˚C, plasma power from 300 to 50 W or plasma exposure time from 6 to 3 s, respectively. Although the high growth rate of ALD film is highly desired in the industry, the film quality should not be neglected. As shown in this work, there is a trade-off between the film properties and film growth rate during SiO2 thin film deposition. In order to balance the throughput and quality of PEALD SiO2 thin film, the plasma power of 180 W and plasma exposure of 3 s was suggested. The studied low-temperature ALD Al2O3 processes included either O2-based PEALD or a process that combines H2O-based thermal ALD with in-situ N2 plasma treatment. For O2-based PEALD, the moisture barrier properties of Al2O3 films were found to be improved with increasing plasma power when the plasma exposure time was relatively short (1 and 3 s). The best water vapor transmission rate of 4-nm thick Al2O3 film was 5×10-3 gm−2day−1. However, a degradation in the moisture barrier properties was observed if the plasma exposure time reached 6 s. This degradation did not occur in the combined process of H2O-based thermal ALD with in-situ N2 plasma treatment. In addition to the moisture barrier properties of Al2O3 thin films, the growth, refractive index, density, roughness and elemental composition were also investigated. Overall, the results demonstrate that with proper PEALD process optimization, it is possible to fabricate high-quality SiO2 and Al2O3 films for thermally sensitive materials/applications.Description
Supervising professor
Savin, Hele, Prof., Aalto University, Department of Electronics and Nanoengineering, FinlandThesis advisor
Savin, Hele, Prof., Aalto University, Department of Electronics and Nanoengineering, FinlandKeywords
atomic layer deposition, plasma-enhanced atomic layer deposition, low temperature, Al2O3, SiO2
Other note
Parts
-
[Publication 1]: Z. Zhu, C. Modanese, P. Sippola, M. Di Sabatino, H. Savin. Nanometerscale depth-resolved atomic layer deposited SiO2 thin films analyzed by glow discharge optical emission spectroscopy. Physica Status Solidi A, 215, 6, 1700864, 2018.
Full text in Acris/Aaltodoc: http://urn.fi/URN:NBN:fi:aalto-201808214586DOI: 10.1002/pssa.201700864 View at publisher
-
[Publication 2]: Z. Zhu, P. Sippola, O.M.E. Ylivaara, C. Modanese, M. Di Sabatino, K. Mizohata, S. Merdes, H. Lipsanen, H. Savin. Low-temperature plasma-enhanced atomic layer deposition of SiO2 using carbon dioxide. Nanoscale Research Letters, 14, 55, 2019.
Full text in Acris/Aaltodoc: http://urn.fi/URN:NBN:fi:aalto-201903052168DOI: 10.1186/s11671-019-2889-y View at publisher
-
[Publication 3]: Z. Zhu, P. Sippola, H. Lipsanen, H. Savin, S. Merdes. Influence of plasma parameters on the properties of ultrathin Al2O3 films prepared by plasma enhanced atomic layer deposition below 100 °C for moisture barrier applications. Japanese Journal of Applied Physics, 57, 12, 125502, 2018.
Full text in Acris/Aaltodoc: http://urn.fi/URN:NBN:fi:aalto-201812216710DOI: 10.7567/JJAP.57.125502 View at publisher
-
[Publication 4]: Z. Zhu, S. Merdes, O.M.E Ylivaara, K. Mizohata, M.J. Heikkilä, H. Savin. Al2O3 thin films prepared by a combined thermal-plasma atomic layer deposition process at low temperature for encapsulation applications. Physica Status Solidi A, 1900237, 2019.
DOI: 10.1002/pssa.201900237 View at publisher
-
[Publication 5]: Z. Zhu, E. Salmi, S. Virtanen. Residual stress study of thin films deposited by atomic layer deposition. In IEEE conference proceeding. IEEE 12th International Conference on ASIC (ASICON), Guiyang, China, 233-236, 2017.
DOI: 10.1109/ASICON.2017.8252455 View at publisher
